Adding Resources to the Concept Car - Revision history

Donald: /* Board Dimensions */

2010-08-17T11:16:14Z

‎Board Dimensions

2010-08-17T07:37:02Z

‎Regarding Upgrades of the ConceptCar

2010-08-06T11:42:46Z

‎Regarding Upgrades of the ConceptCar

2010-08-06T11:42:35Z

‎Regarding Upgrades of the ConceptCar

2010-08-06T11:42:13Z

‎Operational Controls

2010-08-06T11:39:53Z

‎Regarding Upgrades of the ConceptCar

2010-08-06T10:07:34Z

‎Regarding Upgrades of the ConceptCar

2010-08-06T10:07:19Z

‎Regarding Upgrades of the ConceptCar

2010-08-06T10:07:05Z

@@ Line 14: / Line 14: @@
 ==Board Dimensions==
-[[image:StackableBoardLayout.png|thumb|200px|Figure 4.1. Board Dimensions]]
+[[image:StackableBoardLayout.png|frame|Figure 4.1. Board Dimensions]]
 All boards featuring an AT90CAN128 microcontroller are supposed to fit into any of the 8 spaces at the CAN bus box. Therefore they share the same dimensions, drill holes for mounting and SUB-D jack position. They all have the same dimensions to be interchangeable in place.
@@ Line 38: / Line 38: @@
 # Move the drill holes to the positions 4mm apart from each edge
 # Rotate the SUB-D CAN connector to face upwards and move it to position 37.506mm/60.88mm. <tt>MOVE CAN_BUS (37.506mm 60.88mm)</tt> would do this.
 ==Operational Controls==

@@ Line 1: / Line 1: @@
 == Regarding Upgrades of the ConceptCar ==
-[[image:ECU_stack.jpg|thumb|right|250px|The ConceptCar's ECU mount stack (outdated ECU revision)]]
+[[image:ECU_stack.jpg|thumb|right|300px|The ConceptCar's ECU mount stack]]
 The Concept Car has a modular architecture allowing the addition of resources in a simple way. In order to integrate a new ECU into the ConceptCar, these things are important:
 #It is attached to the [[CAN_Bus|CAN bus]], but does not disturb the regular operation of the car. This means that no already used CAN IDs may be overwritten and that the bus load has to be low enough.
@@ Line 9: / Line 9: @@
 This page illustrates the demands regarding the form factor of the small boards so they can fit into the ECU stacks. There they are well mounted and protected against physical damage by the massive metal box next to them.
 ==Board Dimensions==

@@ Line 1: / Line 1: @@
 == Regarding Upgrades of the ConceptCar ==
-[[image:ECU_stack.jpg|thumb|left|250px|The ConceptCar's ECU mount stack (outdated ECU revision)]]
+[[image:ECU_stack.jpg|thumb|right|250px|The ConceptCar's ECU mount stack (outdated ECU revision)]]
 The Concept Car has a modular architecture allowing the addition of resources in a simple way. In order to integrate a new ECU into the ConceptCar, these things are important:
 #It is attached to the [[CAN_Bus|CAN bus]], but does not disturb the regular operation of the car. This means that no already used CAN IDs may be overwritten and that the bus load has to be low enough.

@@ Line 1: / Line 1: @@
 == Regarding Upgrades of the ConceptCar ==
-[[image:ECU_stack.jpg|thumb|right|250px|The ConceptCar's ECU mount stack (outdated ECU revision)]]
+[[image:ECU_stack.jpg|thumb|left|250px|The ConceptCar's ECU mount stack (outdated ECU revision)]]
 The Concept Car has a modular architecture allowing the addition of resources in a simple way. In order to integrate a new ECU into the ConceptCar, these things are important:
 #It is attached to the [[CAN_Bus|CAN bus]], but does not disturb the regular operation of the car. This means that no already used CAN IDs may be overwritten and that the bus load has to be low enough.

@@ Line 40: / Line 40: @@
 ==Operational Controls==
-[[image:Actorboard_boardDesignIllustration.png|thumb|350px|Figure 4.2. An example of good placement of the operational controls and of their labeling.]]
+[[image:Actorboard_boardDesignIllustration.png|frame|right|350px|Figure 4.2. An example of good placement of the operational controls and of their labeling.]]
 These are recommendations on what operational controls to use to supply a uniform look&feel (and in some aspects programming) of the sensor- and actor-boards. The placement is not critical, it just looks better this way.

← Older revision		Revision as of 10:07, 6 August 2010
Line 1:		Line 1:
		+	== Regarding Upgrades of the ConceptCar ==
		+
	[[image:ECU_stack.jpg\|thumb\|right\|The ConceptCar's ECU mount stack]]		[[image:ECU_stack.jpg\|thumb\|right\|The ConceptCar's ECU mount stack]]
	The Concept Car has a modular architecture allowing the addition of resources in a simple way. In order to integrate a new ECU into the ConceptCar, two things are important:		The Concept Car has a modular architecture allowing the addition of resources in a simple way. In order to integrate a new ECU into the ConceptCar, two things are important: