Deployment - Revision history

Dulcineia at 14:43, 20 October 2009

2009-10-20T14:43:40Z

Dulcineia at 14:42, 20 October 2009

2009-10-20T14:42:37Z

Dulcineia at 09:34, 20 October 2009

2009-10-20T09:34:03Z

Dulcineia: New page: NOTOC ==2.3.2. Deployment== ====Table of Contents==== 2.3.2.1. Running the executable ====2.3.2.1. Running the executable==== After install the...

2009-10-20T09:33:35Z

New page: __NOTOC__ ==2.3.2. Deployment== ====Table of Contents==== 2.3.2.1. Running the executable ====2.3.2.1. Running the executable==== After install the...

New page

__NOTOC__

==2.3.2. Deployment==

====Table of Contents====

[[2.3.2.1. Running the executable|2.3.2.1. Running the executable]]

====2.3.2.1. Running the executable====

After install the bootloader on the ARM7 board, following the steps presented in Section [[#2.3.1, the application is ready to be executed.

The bootloader automatically executes the binary from an SD-Card that is inserted into the ARM7's SD card slot at boot time. Therefore, it is necessary to write the application code into one SD-Card with the name app.bin inside the SD-Card root folder.
To boot into the executable make sure the following conditions are met:

*The SD-Card is at most 1GB in size (larger Cards are SD-HC and do not work);
*The SD-Card is formatted with FAT32 file system;
*The executable is stored as the file

app.bin

inside the SD-Cards root folder.

To control the bootloader's work it is easiest to connect to the ARM7 board over UART (115200Baud 8N1) and watch the status messages.

With the SD-Card insert to the SD-Card slot of the board containing the correspondent app.bin file in the root folder, the next step is to press the button Reset in order to execute the application. The Reset button is located in opposite side of the CAN and the RS232 connectors in [[ECU_implementing_Controlboard#1.3.3.2.2._Hardware_description|Figure 1.6]].

← Older revision		Revision as of 14:43, 20 October 2009
Line 16:		Line 16:
	To control the bootloader's work it is easiest to connect to the ARM7 board over UART (115200Baud 8N1) and watch the status messages.		To control the bootloader's work it is easiest to connect to the ARM7 board over UART (115200Baud 8N1) and watch the status messages.

−	With the SD-Card insert to the SD-Card slot of the board containing the correspondent app.bin file in the root folder, the next step is to press the button Reset in order to execute the application. The Reset button is located in opposite side of the CAN and the RS232 connectors in [[ECU_implementing_Controlboard#~~1.3.3.2.2._Hardware_description~~\|Figure 1.6]].	+	With the SD-Card insert to the SD-Card slot of the board containing the correspondent app.bin file in the root folder, the next step is to press the button Reset in order to execute the application. The Reset button is located in opposite side of the CAN and the RS232 connectors in [[ECU_implementing_Controlboard#Hardware_description\|Figure 1.6]].

← Older revision		Revision as of 09:34, 20 October 2009
Line 1:		Line 1:
−	~~__NOTOC__~~
−
	==2.3.2. Deployment==		==2.3.2. Deployment==
−
−	~~====Table of Contents====~~
−
−	~~[[2.3.2.1. Running the executable\|2.3.2.1. Running the executable]]~~

	====2.3.2.1. Running the executable====		====2.3.2.1. Running the executable====

@@ Line 1: / Line 1: @@
-==2.3.2. Deployment==
+==Running the executable==
-−
-====2.3.2.1. Running the executable====
 After install the bootloader on the ARM7 board, following the steps presented in Section [[#2.3.1, the application is ready to be executed.

Deployment - Revision history

Dulcineia at 14:43, 20 October 2009

Dulcineia at 14:42, 20 October 2009

Dulcineia at 09:34, 20 October 2009

Dulcineia: New page: __NOTOC__ ==2.3.2. Deployment== ====Table of Contents==== 2.3.2.1. Running the executable ====2.3.2.1. Running the executable==== After install the...

Dulcineia: New page: NOTOC ==2.3.2. Deployment== ====Table of Contents==== 2.3.2.1. Running the executable ====2.3.2.1. Running the executable==== After install the...